Procedures and test voltage values for acceptance and maintenance testing of electrical submersible pump (ESP) cable systems are presented. This recommended practice applies to cable systems rated 3 kV and 5 kV (phase to phase) and is intended only for this special-purpose cable. The intent is to provide uniform test procedures and guidelines for evaluation of the test results.
- Standard Committee
- IAS/PCI - Petroleum and Chemical Industry
- Status
- Superseded Standard
- PAR Approval
- 1998-09-16
- Superseded by
- 1017-2013
- Superseding
- 1017-1991
- Board Approval
- 2004-09-23
- History
-
- ANSI Approved:
- 2005-03-10
- Published:
- 2005-04-13
Working Group Details
- Society
- IEEE Industry Applications Society
- Standard Committee
- IAS/PCI - Petroleum and Chemical Industry
- Working Group
-
ESP WG - ESP Working Group
Learn More About ESP WG - ESP Working Group - IEEE Program Manager
- Patricia Roder
Contact Patricia Roder - Working Group Chair
- Robert Durham
Other Activities From This Working Group
Current projects that have been authorized by the IEEE SA Standards Board to develop a standard.
P1017.4
IEEE Draft Recommended Practice for Testing and Rating of Electrical Submersible Pump Motors
This standard specifies procedures and test values for testing and rating of Electrical Submersible Pump (ESP) motors as well as installation and handling practices. The specified procedures and test values apply to ESP motor systems rated 3 kV through 8 kV (phase to phase).
Standards approved by the IEEE SA Standards Board that are within the 10-year lifecycle.
1017.1-2021
IEEE Recommended Practice for Testing of Electric Submersible Pump Cable
Procedures and test voltage values for factory, acceptance, and maintenance testing of electric submersible pump (ESP) cable systems are presented. This recommended practice applies to cable systems rated 3 kV through 8 kV (phase to phase) and is intended only for this special purpose cable. The intent is to provide uniform test procedures and guidelines for evaluation of the test results.
1017.2-2021
IEEE Recommended Practice for Specifying Electric Submersible Pump Cable--Ethylene-Propylene Rubber Insulation
Minimum requirements for the design, construction, manufacturing, testing, purchasing, and application of electric submersible pump (ESP) cable are presented. The cable is round or flat, with ethyleneu2013propylene rubber insulation, nitrile jacket, ethyleneu2013propylene diene monomer (EPDM) jacket or metallic barrier, and armor or encapsulating material. These cables are for voltages not exceeding 8 kV (phase to phase) and conductor temperatures not exceeding 140 u00baC (284 u00baF) for nitrile or a maximum of 232 u00baC (450 u00baF) for EPDM jacket or metallic barrier cable. Conductors, insulation, barrier (optional), assembly with or without jacket, armor, requirements for testing by the manufacturer, and cable ampacity are all covered in the document.
1017.3-2021
IEEE Recommended Practice for Specifying Electric Submersible Pump Cable--Polypropylene Insulation
Minimum requirements for the design, construction, manufacturing, testing, purchasing, and application of electric submersible pump cable are presented. The cable is round or flat, with polypropylene insulation, nitrile or polypropylene jacket, or metallic barrier or armor. These cables are for voltages not exceeding 8 kV (phase to phase) and conductor temperatures not exceeding 96 u00b0C (205 u00b0F) maximum or u201310 u00b0C (14 u00b0F) minimum. Conductors, insulation, barrier(optional), assembly with or without jacket, and armor or encapsulating material, requirements for testing by the manufacturer, and cable ampacity are all covered in the document.
These standards have been replaced with a revised version of the standard, or by a compilation of the original active standard and all its existing amendments, corrigenda, and errata.
1017-2013
IEEE Recommended Practice for Field Testing Electric Submersible Pump Cable
Procedures and test voltage values for acceptance and maintenance testing of electric submersible pump (ESP) cable systems are presented. This recommended practice applies to cable systems rated 3 kV and 5 kV (phase to phase) and is intended only for this special-purpose cable. The intent is to provide uniform test procedures and guidelines for evaluation of the test results.
1018-2004
IEEE Recommended Practice for Specifying Electric Submersible Pump Cable - Ethylene-Propylene Rubber Insulation
Minimum requirements for the construction, manufacturing, purchasing, and application of electric submersible pump cable are presented. The cable is round or flat, with ethyleneu2013 propylene rubber insulation, nitrile jacket, ethyleneu2013propylene diene monomer (EPDM) jacket or lead sheath, and armor. These cables are for voltages not exceeding 3 kV or 5 kV (phase to phase) and conductor temperatures not exceeding 140 u00baC (284 u00baF) for nitrile or a maximum of 204 u00baC (400 u00baF) for EPDM jacket or lead sheath cable. Conductors, insulation, barrier (optional), assembly and jacket, armor, requirements for testing by the manufacturer, and cable ampacity are covered.
1018-2013
IEEE Recommended Practice for Specifying Electric Submersible Pump Cable--Ethylene-Propylene Rubber Insulation
Minimum requirements for the design, construction, manufacturing, testing, purchasing, and application of electric submersible pump (ESP) cable are presented. The cable is round or flat, with ethyleneu2013propylene rubber insulation, nitrile jacket, ethyleneu2013propylene diene monomer (EPDM) jacket or lead sheath, and armor. These cables are for voltages not exceeding 3 kV or 5 kV (phase to phase) and conductor temperatures not exceeding 140 u00baC (284 u00baF) for nitrile or a maximum of 232 u00baC (450 u00baF) for EPDM jacket or lead sheath cable. Conductors, insulation, barrier (optional), assembly with or without jacket, armor, requirements for testing by the manufacturer, and cable ampacity are all covered in the document.
1019-2004
IEEE Recommended Practice for Specifying Electric Submersible Pump Cable - Polypropylene Insulation
Minimum requirements for the construction, manufacturing, purchasing, and application of electric submersible pump cable are presented. The cable is round or flat, with polypropylene rubber insulation, nitrile jacket, and armor. These cables are for voltages not exceeding 3 kV or 5 kV (phase to phase) and conductor temperatures not exceeding 96 u00baC (205 u00baF) for nitrile or a maximum of u201310 u00baC (14 u00baF). Conductors, insulation, assembly and jacket, armor, requirements for testing by the manufacturer, and cable ampacity are covered.
1019-2013
IEEE Recommended Practice for Specifying Electric Submersible Pump Cable–Polypropylene Insulation
Minimum requirements for the design, construction, manufacturing, testing, purchasing, and application of electric submersible pump cable are presented. The cable is round or flat, with polypropylene rubber insulation, nitrile or polyethylene jacket, and armor. These cables are for voltages not exceeding 3 kV or 5 kV (phase to phase) and conductor temperatures not exceeding 96 u00baC (205 u00baF) maximum for nitrile or a maximum minimum of u201310 u00baC (14 u00baF) minimum. Conductors, insulation, assembly and with or without jacket, armor, requirements for testing by the manufacturer, and cable ampacity are all covered in the document.
These standards have been removed from active status through a ballot where the standard is made inactive as a consensus decision of a balloting group.
No Inactive-Withdrawn Standards
These standards are removed from active status through an administrative process for standards that have not undergone a revision process within 10 years.
No Inactive-Reserved Standards